Description
Product introduction
Adapt To ORTUR Laser Machine
Ortur is advertising real Optical Power output in all the 2nd Generation Module Labels. There are in the market many products with impossible claims of power output. These are simply impossible with current diode technology. We give our users and customers the real specifications, in order to allow an informed purchase decision. Ortur Laser modules dot size are measured by engraving on real-world products and materials. The Laboratory results can be significantly better, but are of no consequence for the users. As a rule of thumb: More power is not always better. Engraving results benefit from a finer/smaller dot size and less power. Cutting on the other hand requires the opposite: More power, which consequently forces the dot size to be bigger.
LU2-4-SF 24V Short Focus
|
Product Name
|
LU2-4-SF 24V Short Focus Laser Module
|
|
Optical Power
|
4500- 5500 mW
|
|
Focal Spot
|
About 0.12×0.15 MM
|
|
Light Path
|
Focused Beam
|
|
Focal Length
|
30 MM
|
|
Electric Current
|
3.4-3.6 A
|
|
Wavelength
|
445+10 NM
|
|
Voltage
|
4.2-5.0 V
|
|
Product Size
|
40x41x122 MM
|
TIPS:
1. LU2-4-SF is good at cutting and better at engraving harder materials (such as stainless steel and other hard materials), and could support a higher speed.
2. It is not that the smaller the light spot, the better the effect. When engraving photos, you may need to increase the laser spot to get a better picture effect.
Laser Shield can act as a shield, effectively reducing the damage to the eyes caused by the laser. But still can’t stare at the
laser for a long time, which will cause irreversible damage.
laser for a long time, which will cause irreversible damage.
When the laser shield of the laser module, the focal gauge board and the laser engraved object are attached to each other, the focusing is completed. Before starting to engrave or cut, grasp the hole of the focal gauge board with your fingers, and drag the focal gauge board out.
LU2-4-LF 24V Long Focus
|
Product Name
|
LU2-4-LF Long Focus Laser Module
|
||||||
|
Optical Power
|
4500- 5500 mW
|
||||||
|
Focal Spot
|
About 0.1 7×0.25 MM
|
||||||
|
Light Path
|
Focused Beam
|
||||||
|
Focal Length
|
50 MM
|
||||||
|
Electric Current
|
3.4-3.6 A
|
||||||
|
Wavelength
|
445+10 NM
|
||||||
|
Voltage
|
4.2-5.0 V
|
||||||
|
Product Size
|
40×41.5×1 10 MM
|
||||||
TIPS:
1. LU2-4-LF is good at engraving and better at cutting, and1. LU2-4-LF is good at engraving and better at cutting, and could support a higher speed.
2. It has the air assist, but you need to buy a Air Compressor to support the air assist.
3. It is not that the smaller the light spot, the better the effect.When engraving photos, you may need to increase the laser spot to get a better picture effect.
3. It is not that the smaller the light spot, the better the effect.When engraving photos, you may need to increase the laser spot to get a better picture effect.
Shading acrylic can act as a shield, effectively reducing the damage to the eyes caused by the laser. But still can’t stare at the laser for a long time, which will cause irreversible damage.
Loosen the thumbscrews on both sides, you can adjust the up and down position of the laser shield, or the angle of rotation to suit your personal usage habits.
LU2-2 Laser Module
|
Product Name
|
LU2-2 24V Laser Module
|
|
Optical Power
|
1000-1600 mW
|
|
Focal Spot
|
About 0.07×0.06 MM
|
|
Light Path
|
Focused Beam
|
|
Focal Length
|
50 MM
|
|
Electric Current
|
1.1-1.35 A
|
|
Wavelength
|
445±10 NM
|
|
Voltage
|
5-6 V
|
|
Product Size
|
40×41.5×96 MM
|
TIPS:
1. LU2-2 is good for engraving high-precision pattern, but speed couldn’t be set too high.
2. It’s not good at cutting.
3. It is not that the smaller the light spot, the better the effect. When engraving photos, you may need to increase the laser spot to get a better picture effect.
3. It is not that the smaller the light spot, the better the effect. When engraving photos, you may need to increase the laser spot to get a better picture effect.
Shading acrylic can act as a shield, effectively reducing the damage to the eyes caused by the laser.But still can’t stare at the laser for a long time, which will cause irreversible damage.
Loosen the thumbscrews on both sides, you can adjust the up and down position of the laser shield, or the angle of rotation to suit your personal usage habits.
About Ortur
Ortur’s Mission
Ortur is a high-tech manufacturer focus on developing diode laser engravers founded by a group of passionate engineers. We love to discover the unknown and try to develop our products to the next level with vitality and creativity.
Ortur is committed to expanding the use boundary of diode laser engravers and exploring more application scenarios of diode laser.In the next two years, Ortur’s mission is to create safer, more efficient,and more user-friendly multipurpose diode laser engravers, to provide more chances for small businesses,workshops, artists, engineers, and self-employed workers to improve their efficiency.
In future, Ortur will develop a small CNC machine to meet more demands from our users, to bring them more business opportunities and more possibilities.
Always on the way to try the best. Startup with creative imagination, find out the most adaptive design, always provide the outstanding product!
Our Certificate
Reviews
There are no reviews yet.